Looking for Hinomoto C142 parts? Browse our complete range of compatible spare and maintenance parts for the Hinomoto C142 mini tractor—including filters, engine parts, cooling, electrical, and hydraulic components—available directly from stock for fast worldwide delivery.
| Specification | Value |
|---|---|
| General | |
| Brand | Hinomoto |
| Model | C142 |
| Series | Hinomoto C-serie |
| Build years | 1980-1986 |
| Engine | Toyosha CS86 View → |
| Bore x stroke | 70 x 75 mm |
| Power (indicative, not from manual) | 17 hp gross |
| Cylinders | 3 |
| Compression | 23:1 |
| Static injection timing | 25 degrees before TDC |
| Starter motor | Hitachi with built-in reduction, brushes new 16 mm, minimum 11 mm |
| Cylinder bore | 70.000 to 70.019 mm |
| Cooling system | 3.0 L |
| Engine oil with filter | 2.5 L (later engines with two drain plugs: 3.0 L) |
| Gross engine power (indicative) | 17 hp |
| Fuel filter glass bowl | Check daily for water |
| Fuel filter | Every 200 hours |
| Air filter | The workshop manual does not specify a value for this |
| Engine oil filter | The workshop manual does not specify a value for this |
| Injection pump runs dry | Too little oil in its own crankcase |
| Starter motor does nothing | Safety start switch, fuse, ground cable |
| Stalling on a slope or when fuel is low | Return line, filter, low tank level |
| Black smoke, low power | Air filter, injectors, injection timing |
| Glass fuel filter housing | Glass fuel filter housing (SKU-15009) View → |
| Drivetrain | |
| Drive | 2WD / 4WD |
| Idle speed | 850 to 900 rpm |
| Maximum no-load speed | 2650 to 2700 rpm |
| Gearbox speeds | 3 forward and 1 reverse in 2 groups, giving 6 forward and 2 reverse |
| Transmission, rear axle and hydraulics (shared) | approx. 17 L |
| Transmission and hydraulics | Transmission oil GL-4 10 L (SKU-15W402) View → |
| Brake pedal travel | 20 to 30 mm, equal left and right |
| Brake shoe minimum | 2.0 mm |
| Brake drum maximum | 122 mm |
| Clutch pressure plate | 29 Nm (6 bolts) |
| Engine to clutch housing | 70 Nm |
| Transmission, rear axle, and hydraulics (shared) | approx. 17 L |
| Transmission oil | Transmission oil GL-4 10 L (SKU-15W402) View → |
| Clutch kit | Clutch kit (8720297954030) View → |
| PTO and hitch | |
| PTO | 540 rpm with built-in freewheel |
| PTO power (indicative) | unknown |
| Hydraulic pump | Hydraulic pump (SKU-115008) View → |
| PTO oil seal | PTO oil seal 40x55x10 (SKU-96078) View → |
| Capacities | |
| Cooling system | 3.0 L |
| Transmission, rear axle and hydraulics (shared) | approx. 17 L (80W GL-4) View 80W GL-4 → |
| Front axle center housing (4WD) | 1.5 L (80W90) View 80W90 → |
| Injection pump separate sump | 200 ml engine oil |
| Engine oil | Engine oil 15W-40 5 L (SKU-15W40) View 15W40 → |
| Capacity | 865 cc |
| Other | |
| Displacement | 865 cc |
| Sister model | Massey Ferguson 1010 |
| Firing order | 1-3-2 |
| Nominal rpm | 2500 rpm |
| Valve springs per valve | 1 |
| Oil pressure | approx. 1.0 bar at 800 rpm, approx. 4.9 bar at 2700 rpm |
| Thermostat | starts opening at 69 to 73 °C, fully open at 85 °C |
| Radiator cap | opens at approx. 0.9 bar |
| Alternator | permanent magnet with 8 poles, 12.5 A at 14 V, charge light off at approx. 1400 rpm engine speed |
| Voltage regulator | 14 to 15 V, separately mounted, non-adjustable |
| Piston skirt | 69.91 to 69.93 mm |
| Piston pin | 23.990 to 23.996 mm |
| Piston clearance | 0.07 to 0.109 mm |
| Main journal | 59.960 to 59.985 mm |
| Crankpin journal | 47.960 to 47.980 mm |
| Bearing clearance | 0.03 to 0.095 mm, maximum 0.15 mm |
| Crankshaft end play | 0.1 to 0.3 mm |
| Steering ratio | 10:1 |
| Battery | 12 V, negative earth |
| Front axle (4WD) | Front axle oil 80W-90 GL-4 4 L (SKU-80W90) View → |
| Daily | Check fuel filter glass for water |
| After the first 50 hours (also after overhaul) | Replace transmission and hydraulic oil and hydraulic filter |
| Every 100 hours or every two weeks | Check injection pump oil level |
| Every 200 hours | Replace fuel filter, replace transmission and hydraulic oil and hydraulic filter |
| Every 400 hours | Change injection pump oil (200 ml engine oil), clean and grease 2WD front wheel bearings |
| Every six months | Remove injectors and install new gasket ring |
| Valve clearance cold, intake | 0.30 mm |
| Valve clearance cold, exhaust | 0.35 mm |
| Valve adjuster locknut | 44 Nm |
| Valve cover nuts | 2 to 3 Nm |
| Rocker arm shaft | 30 to 39 Nm |
| V-belt deflection | 8 to 10 mm |
| Clutch pedal free play | 15 to 20 mm |
| Toe-in 2WD | 3 to 10 mm |
| Toe-in 4WD | maximum 5 mm toe-in or 5 mm toe-out |
| Front axle wheel bolts | 88 Nm (2WD), 87 Nm (4WD) |
| Glow plug | approx. 0.23 ohm each, 15 to 19 Nm |
| Injector holder in head | 58 Nm |
| Injector opening pressure | minimum 132 bar, adjust to 138 to 146 bar |
| Lift relief pressure | 139 to 144 bar |
| Crankshaft pulley nut | 98 Nm |
| Flywheel bolts | 44 to 49 Nm |
| Hydraulic filter | After the first 50 hours, then every 200 hours, together with the transmission and hydraulic oil |
| Boiling over after approx. 20 minutes | Radiator core, cooling system, radiator cap, water pump, V-belt, or thermostat |
| White or blue smoke, misfiring | Sealing ring under the injector or injector |
| Difficult starting when cold | Glow plug |
| Hitch jerks | Pump gets too little oil |
| Oil pressure light stays on | Oil pressure switch, oil level, suction pipe, relief valve |
| Water in the diesel | Long period of inactivity |
| Charging | Turns off at approx. 1400 rpm of the engine |
| Preheating | Illuminates in the GLOW position, not in the start position |
| Valve clearance cold | intake 0.30 mm, exhaust 0.35 mm |
| Filter kit | Filter kit C142-C174 (SKU-10035) View → |
| Front axle oil (4WD) | Front axle oil 80W-90 GL-4 4 L (SKU-80W90) View → |
| Radiator flush | Radiator flush 250 ml (SKU-125007) View → |
| Water pump | Water pump CS86/CS100/CS112 (SKU-292) View → |
| Head gasket | Head gasket CS86 C142/C144 (SKU-51) View → |
| Gasket set | Gasket set C142-C174 (VAR-0010), choose the version per engine View → |
| Piston rings | Piston rings 70 mm C142/C144 (SKU-95087) View → |
| Injector | Injector nozzle with sealing rings (SKU-47036-s) View → |
Maintaining or repairing your Hinomoto C142 mini tractor starts with parts that fit accurately. On this page you will find all compatible Hinomoto C142 spare parts—from oil, fuel, and air filters to water pumps, radiator hoses, clutches, brakes, front axle seals, three-point linkage parts, and electrical components. Use the category filter to quickly jump to the exact assembly for your Hinomoto C142.
Looking for parts for another Hinomoto model? View our complete range of Hinomoto mini tractor parts or contact our team for expert support.