Looking for Iseki TM15 parts? Browse our complete range of compatible spare and maintenance parts for the Iseki TM15 mini tractor—including filters, engine parts, cooling, electrical, and hydraulic components—available directly from stock for fast worldwide delivery.
| Specification | Value |
|---|---|
| General | |
| Brand | Iseki |
| Model | TM15 |
| Series | Iseki TM-serie |
| Build years | 1993-1999 |
| What to look for when buying | Inspection points, common issues and price guide View buying guide → |
| Engine | Iseki E393 View → |
| Power | 10.9 kW / 14.8 hp at 2500 rpm |
| Fuel | Diesel gas oil (JIS 2, JIS 3 in severe frost) |
| Cold start | Have the engine started from cold. Difficult starting often points to worn glow plugs, a contaminated fuel filter, or air in the fuel system. |
| Air filter element | 1675-104-210-0 |
| Fuel filter (complete) | 1600-105-230-0 |
| Fuel filter element | 1514-102-011-0 |
| Engine oil filter (cartridge) | 6213-240-002-0 |
| Ignition switch or starter motor defective | Test and repair or replace. |
| Air in the fuel system | Bleed the system via the bleed screw until bubble-free diesel comes out. |
| Fuel filter clogged | Clean the filter bowl, replace the element. |
| No fuel supply | Open the fuel tap, check the tank content; watch for paraffin waxing in frost (use winter diesel). |
| Glow plugs worn (cold start) | Test the glow plugs (measure resistance or check current draw) and replace. From practical experience: a TM that starts fine warm but not cold almost always has a glow plug or fuel issue. |
| High oil consumption, blue smoke, low compression on multiple cylinders | Worn piston rings. Replacement is possible without a full engine overhaul; new piston rings for the E393/E3100 (SKU-95066) are available per cylinder. View → |
| Drivetrain | |
| Drive | Four-wheel drive (4WD) |
| Clutch | Dry single plate |
| Brakes | Mechanical drum brakes (dry) |
| Transmission | Sliding gear (selective gearing), 6 forward + 2 reverse |
| Rotor speed | 156 / 242 / 396 rpm (246 rpm reverse) |
| Project machine (starting problems, smoking engine, worn clutch) | below that — factor in overhaul costs |
| Clutch and thrust bearing | Engage the clutch and listen for squealing or grinding noises: the thrust bearing is a known wear part. Pedal play should be 20–30 mm. |
| Clutch pedal play | 20–30 mm |
| Brake pedal play | 20–30 mm |
| Clutch pedal not depressed | The starter safety switch blocks the starter. Fully depress the pedal — this is by far the most common "fault". |
| Oil leak between engine and clutch housing | Worn rear crankshaft seal — a well-known age-related issue with these engines. Replace it right away while the clutch is out anyway. |
| Dimensions | |
| Length | 2000 mm |
| Width | 1060 mm |
| Height | 1190 mm (without frame), 1885–1940 mm (with ROPS) |
| Ground clearance | 265 mm |
| Weight | 550–580 kg |
| Wheelbase | 1320 mm |
| Front track width | 755 mm |
| Rear track width | 820 or 930 mm (adjustable) |
| Front tires | 5.00-12 |
| Rear tires | 8-18 |
| Minimum turning radius | 1.7 m |
| Working width | 120 cm |
| Front axle support longitudinal play | 0.1–0.3 mm |
| Front tire pressure | 1.2 kgf/cm² (≈ 1.2 bar) |
| Rear tire pressure | 1.6 kgf/cm² (≈ 1.6 bar) |
| 7. Tyres and storage | Bring tyre pressure up to spec (front 1.2 / rear 1.6 bar), store the machine in a dry, ventilated place, lower the implement and lock the hydraulics. Remove the key. |
| PTO and hitch | |
| Max. PTO power | 9.8 kW / 13.3 hp |
| PTO clutch | Dry single plate (via main clutch) |
| PTO speeds | 450 / 696 / 1140 rpm at 2500 engine rpm |
| PTO reverse setting | 707 rpm (rotating in reverse) |
| PTO shaft | 35 mm, 6 splines |
| Capacities | |
| Fuel tank | 13.5 liters |
| Engine oil | 2.7 liters (15W40) View 15W40 → |
| Cooling system (radiator) | 5.0 liters |
| Transmission / hydraulics | 13.5 liters (U version: 14 liters) (UTTO / GL-4) View UTTO / GL-4 → |
| Front axle (4WD) | 2.7 liters (80W90) View 80W90 → |
| Steering gearbox | Top up to level |
| Grease nipples | As needed |
| Other | |
| Machine code | T0284 |
| Design | Water-cooled, 4-stroke, 3-cylinder diesel |
| Displacement | 928 cc |
| Battery | 12 V / 28 Ah |
| Steering | Power steering (U-type) or mechanical |
| Low 1 | 0.82 |
| Low 2 | 1.28 |
| Low 3 | 2.11 |
| High 1 | 4.98 |
| High 2 | 7.75 |
| High 3 | 12.80 (max. 14.08) |
| Reverse low | 1.08 |
| Reverse high | 6.54 |
| Hitch | Fixed hitch |
| Lift system | Position control |
| Implement attachment | 2P mounting for the rotary tiller (2-point quick-hitch system) |
| Working depth | up to approx. 16 cm |
| Blades | C140 left/right ×13 + C149 ×1 |
| Standard tiller | ARM12 (120 cm) |
| Standard / P / P1 | Tires 5.00-12 front and 8-18 rear, ground clearance 290 mm. P versions have a safety frame (ROPS). |
| ND / NDP / NDP1 | Lower version with tires 5-12 front and 8-16 rear, ground clearance 265 mm, and a slightly shorter machine (2000 mm). Driving speeds are a fraction lower. |
| U | Version with power steering (U-type); transmission capacity here is 14 instead of 13.5 liters. |
| S | Version in which the engine is stopped via the main switch (as with the TM17); the standard TM15 has a separate stop button. |
| Well-maintained dealer machine, low hours (500–1000 hrs), often with tiller | €4,000 – €5,000 |
| Average condition, higher hours or private sale | €2,500 – €4,000 |
| Start safety switch | The engine should only start with the clutch pedal depressed. If it starts without this, the safety switch is faulty or bypassed. |
| Front axle (4WD) | Check the front axle oil (2.7 liters) for milky contamination and listen for play; the front axle support should have no more than 0.1–0.3 mm of longitudinal play. |
| Steering play | A maximum of 30–60 mm of play at the steering wheel rim is normal; more indicates wear in the steering box or tie rods. |
| Smoke under load | White smoke indicates a contaminated air filter or too much engine oil; black smoke points to incorrect fuel or injector problems; blue smoke indicates oil consumption (piston rings). |
| Hour meter and maintenance | Ask about maintenance: engine oil should be changed every 100 hours, transmission oil every 300 hours. |
| First 50 hours (break-in service) | Replace engine oil, replace oil filter, replace transmission oil, clean hydraulic suction filter. This first service is important: break-in debris needs to be removed. |
| Every 50 hours | Grease all lubrication points with lithium grease (in wet soil or intensive tilling: daily). |
| Every 100 hours | Replace engine oil. Clean air filter element. Clean fuel filter bowl. Check battery fluid. Check front axle oil. Inspect rubber hoses and lines. |
| Every 200 hours | Clean hydraulic suction filter. |
| Every 300 hours | Replace oil filter. Replace fuel filter element. Replace transmission oil. Have steering play and tire pressure checked/adjusted, have throttle and speed adjustment set. |
| Every 600 hours | Replace front axle oil (4WD). |
| Annually | Replace coolant. Check electrical wiring. Check clutch housing for oil leaks via the drain plug. |
| V-belt (fan belt) | 8–10 mm deflection |
| Steering wheel play | 30–60 mm |
| 1 | 450 rpm |
| 2 | 696 rpm |
| 3 | 1140 rpm |
| Reverse | 707 rpm (reverse) |
| Rotary tiller 120–130 cm | Yes — this is what the machine was built for |
| Flail/rotary mower up to approx. 1.2 m | Yes, a great combination |
| Snow blade / sweeper | Yes |
| Small tipping trailer on the fixed towbar | Yes, watch the low unladen weight (±580 kg) when braking on slopes |
| Wood chipper | Only light models for thin pruning wood |
| Heavy tedder, baler, large rotary mower | No — PTO power is too limited for this |
| Hydraulic suction filter | 1427-503-006-1 |
| 1. Cleaning | Thoroughly clean the machine and let it dry; caked-on dirt holds moisture and causes rust. Touch up bare spots. |
| 2. Check the antifreeze | Test the cooling system (5 litres) for strength or refresh it annually with LLC antifreeze. Without proper antifreeze, the block or radiator can crack in frost. |
| 4. Oil and filters | If a service is due, do it before storage — old, acidic oil attacks bearings while the machine is standing still. |
| 5. Battery | Disconnect or remove the battery (12V 28Ah), store it in a frost-free place and top up the charge every 4–6 weeks. A flat battery will freeze and will then need replacing. |
| 6. Lubricating | Grease all lubrication points, and lightly oil bare metal parts (lift arms, track rods). |
| 8. Run it monthly | During long-term storage, start the engine occasionally and let it reach operating temperature — this lubricates the engine and keeps the fuel pump and seals supple. |
| Safety switch defective | Test the switch at the clutch pedal and replace if necessary. |
| Battery dead | Charge or replace the battery (12V 28Ah). |
| Battery terminals or earth cables loose/corroded | Clean the connections, tighten and grease them. A classic issue on older grey-import machines. |
| Starter turns too slowly | Weak battery, poor earth connection, or engine oil too thick. In practice, a heavy-turning engine can also be caused by a seized thrust bearing — recognizable by noise when the clutch is engaged. |
| V-belt loose or damaged | Adjust tension to 8–10 mm deflection or replace the belt. |
| Radiator dirty | Blow out the fins — the radiator clogs quickly during milling work. |
| Thermostat stays closed | Test the thermostat (opens at 82°C) in a pan of hot water and replace if necessary. |
| Water pump leaking or not pumping | Leakage at the inspection hole under the pump = water pump (SKU-320) replace — supplied including gasket. View → |
| 4 | Put the main gear lever in neutral. |
| 5 | Put the PTO lever in neutral. |
| 6 | Pull the throttle lever to about halfway. |
| 7 | Turn the key to the "drive/preheat" position. Check that the oil pressure light, the charge light and the glow plug light are on. |
| 8 | Wait until the glow plug light goes out, then turn the key further to "start". Release the key immediately once the engine is running. |
| 9 | Check that the oil pressure light and charge light are now off. If either one stays on: switch off the engine immediately and find the cause. |
| Above 0 °C | 5–10 minutes |
| 0 to −10 °C | 10–20 minutes |
| −10 to −20 °C | 20–30 minutes |
| Below −20 °C | At least 30 minutes |
Maintaining or repairing your Iseki TM15 mini tractor starts with parts that fit accurately. On this page you will find all compatible Iseki TM15 spare parts—from oil, fuel, and air filters to water pumps, radiator hoses, clutches, brakes, front axle seals, three-point linkage parts, and electrical components. Use the category filter to quickly jump to the exact assembly for your Iseki TM15.
Looking for parts for another Iseki model? View our complete range of Iseki mini tractor parts or contact our team for expert support.