- Oil Seal - oil seal suitable for the front axle in the tractors shown below. With great care, the models at this seal were sought!
- Technical data
- 35х52х12
- Iseki
- TX145, TX155, TX1000, TX1210, TX1300, TX1410, TX1500, TX1510, TX2140, TX2160
- Rear axle seal for rear axle stub axle seal
- Technical data
- 50x80/85x14/16
- Kubota
- Aste - A15, A17, A19, A155, A175, A195
- Front axle seal / Thrust seal / steering fusee suitable for:
- Iseki
- TL1900, TL1901, TL2100
- TU125, TU1400, TU1500, TU1600, TU1401, TU1501, TU1601
- TU1700, TU1701, TU1900, TU1901, TU2100, TU2101
- Kubota Front axle seal - oil seal - steering knuckle seal transmission
- Technical data
- Height 15mm
- Outside diameter 80mm
- Diameter inside 62mm
- Front axle seal / Thrust seal / steering fusee suitable for:
- Technical data
- 50x68x14mm
- Iseki
- Iseki TA landleader Front axle seal - oil seal - steering knuckle seal transmission rear axle
- A leaking front axle oil seal is common in the TA series! Replace early, before all the oil disappears from the front axle!
- Technical data
- Total Height 19mm
- Outside diameter 79mm
- Rear axle seal suitable for the following models;
- Hinomoto
- E21, E23, E25, E28, E2002, E2004, E222, E224, E230, E2302, E2304, E262, E264, E280, E2602, E2604
- N189, N229, N239, N249
- Massey Ferguson
- Oil Seal - oil seal front axle differential suitable for
- Technical data
- 80x100x14.5mm
- Kubota
- L1-18(note thicker front axle), L1-20(note thicker front axle), L1-22, L1-24, L1-185, L1-205, L1-225, L1-245
- Kubota Sunshine L1-18 to L1-265 Front axle seal - oil seal - steering knuckle seal transmission
- Technical data
- Height 19mm
- Outside diameter 58mm
- Diameter inside 35mm
- Technical data
- Dimensions 35x55x10
- Iseki - Rear PTO
- TX1000, TX1210, TX1300, TX1410, TX1500, TX1510, TX2140, TX2160, TX145, TX155
- TX1000F, TX1210F, TX1300F, TX1410F, TX1500F, TX1510F, TX145F, TX155F, TX2140F, TX2160F
- Front axle seal / Thrust seal / steering fusee suitable for:
- Kubota
- L1501, L1501DT, L1501-AC, L1511, L1801, L1801DT, L2201, L2201DT, L2201-AC
- L185, L245, L185DT, L245DT
- Zen-noh
- Oil Seal seal Kubota
- Technical data
- 52x85x16mm
- Hinomoto
- NX19, NX21, NX23, NX25, NX27, NX220
Seals for Mini Tractors
What is a seal and why is it important?
Seals are small but essential components used throughout your mini tractor’s engine, transmission, and axle systems. Their primary role is to prevent oil, grease, or hydraulic fluid from leaking out, while also keeping dirt, dust, and moisture from entering sensitive areas. By ensuring tight sealing, these components protect key parts such as the clutch, gearbox, differential, and wheel hubs from premature wear and damage.
A worn or damaged seal can result in fluid leaks, contamination, increased friction, and eventually serious mechanical faults. Replacing seals in time is crucial to maintaining efficiency, extending the lifespan of vital components, and reducing costly downtime.
How to choose the right seal
The correct seal depends on the brand, model, and component in which it is used (e.g. clutch seal, axle seal, transmission seal). Each seal is designed for a specific application and must fit with precision to function effectively. Always check compatibility with your tractor before placing an order.
Not sure what seal you need? Contact our customer service – we will help you identify the correct type and size to ensure a perfect fit.
Replacing a seal
While the replacement steps vary depending on the component, the general procedure is similar:
- Preparation: Switch off the tractor, disconnect the battery if needed, and make sure the area around the seal is clean.
- Disassembly: Remove surrounding parts to gain access to the seal (for example, the transmission, clutch housing, or axle hub).
- Remove the old seal: Carefully extract the worn or damaged seal with the appropriate tool, avoiding scratches to the surfaces.
- Install the new seal: Press the new seal smoothly and evenly into place, ensuring proper seating and orientation.
- Reassembly and testing: Reinstall all parts, refill fluids if necessary, and test the tractor to confirm no leaks remain.
Thanks to the precise fit of our seals, replacement is straightforward and restores reliable protection against leaks and contamination.
Why choose Shop4trac for your seals?
At Shop4trac, we supply only high-quality seals from trusted manufacturers. All our seals are thoroughly tested for durability, material strength, and resistance to heat, pressure, and oil. With fast delivery and professional customer service, we ensure that your tractor is back to work quickly and reliably.
Whether you need a seal for the clutch, transmission, axle, or wheel hub of your Iseki, Yanmar, Kubota, or Shibaura, Shop4trac provides the quality components and service you deserve.
