Clutch kit Yanmar Ke-2 | Ke-3 | Ke-4 | Ke-20T | Ke-40 | Ke-60 | Ke-140 | Ke-160 – 180mm 10 splines

Description

Complete clutch kit for Yanmar Ke-series compact tractors. Includes all three parts that wear out during a clutch job: the pressure plate, the clutch disc, and the release bearing. Since you have to remove the transmission anyway, it's a waste to only replace the disc and have to start over six months later because the bearing starts squeaking.

Assembled based on the original Yanmar parts manuals for the Ke-40 (KE40.92250) and the Ke-140 / Ke-160 (NPC-3970).

✔️ 3-in-1 kit — pressure plate, clutch disc, and release bearing, more affordable together than separately
✔️ Clutch disc 180 mm with 10 splines and hub 19.05 mm (3/4") — exact OEM size
✔️ Release bearing type Koyo/JTEKT CT35S, sealed and pre-greased — re-greasing not necessary

Kit contents:

• 1× Pressure plate — OEM 194215-21700 / 194215-21701
• 1× Clutch disc 180 mm, 10 splines, hub 19.05 mm — OEM 194440-21400 / 198165-21450 / 198421-21402
• 1× Release bearing CT35S, 35 × 57 × 14 mm — OEM 194300-22240

Technical specifications:

• Clutch disc: Ø 180 mm (7¼"), hub bore 19.05 mm (3/4"), 10 splines
• Pressure plate: Ø 230 mm total, pressure surface Ø 180 mm, height 40 mm
• Release bearing: bore Ø 35 mm, outer Ø 57 mm, width 14 mm, type CT35S (Koyo / JTEKT)
• Clutch type: dry single plate clutch

Suitable for:

Yanmar

• Ke-2A, Ke-2D, Ke-2DF, Ke-2DN, Ke-2DL
• Ke-3A, Ke-3D, Ke-3DA, Ke-3DAU
• Ke-4A, Ke-4DA
• Ke-20T, Ke-40, Ke-60, Ke-140, Ke-160

OEM for reference:

• 194215-21700, 19421521700 – pressure plate (Ke-40)
• 194215-21701, 19421521701 – pressure plate (Ke-140, Ke-160)
• 194440-21400, 19444021400 – clutch disc (original number)
• 198165-21450, 19816521450 – clutch disc (subsequent number, Ke-140 / Ke-160)
• 198421-21400, 198421-21401, 198421-21402 – clutch disc Ke-series, successive versions (Ke-40)
• 194510-21400, 194515-21400, 194215-21400 – clutch disc, alternative numbers
• 194300-22240, 19430022240 – release bearing, type CT35S

Please note — check your release bearing first. The clutch disc of the Ke-series is the same as that of the Yanmar F- and YM-series, but the release bearing differs: Ke = 35 × 57 × 14 mm, F/YM = 40 × 64 × 16 mm. Measure your old bearing if you are unsure about your version.

Assembly tip: clean the splines of the input shaft and apply a thin layer of heat-resistant clutch grease — truly thin, as grease getting onto the friction lining will cause the clutch to slip. Center the disc carefully before tightening the pressure plate crosswise and evenly.